Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Before
After
Before
After
Before
AfterWindows & Doors in Hollister, CA
Window installation in Hollister runs $450-$1,800 per window, depending on the unit, the framing condition, and how far out of square the opening has drifted. Hollister sits directly on the Calaveras Fault, and the continuous ground creep here gradually racks door frames and distorts window openings in ways installers in most other cities never see. If you’re pricing replacement windows or doors, call (509) 265-6387 and we’ll give you a written estimate based on a measured survey you keep.
Why Hollister Homes Are Different
Hollister is one of the few places in California where window and door work regularly starts with a framing diagnosis rather than a tape measure. The Calaveras Fault runs beneath the city, and its slow, continuous movement, called aseismic creep, physically distorts openings over time. A window that measured square when the house was built in 2004 may be off by a quarter inch today. Doors bind. Weatherstripping fails along one edge. Latch plates stop aligning. None of that is installation error. It’s the ground moving under the house.
The housing stock splits two ways. Downtown and the streets around it hold Craftsman and early-20th-century wood-frame homes, many still carrying original single-pane wood sashes that have weathered decades of drift. The east and north sides of Hollister grew fast in the 1990s and 2000s with tract subdivisions, and those homes often have builder-grade vinyl windows whose insulated glass seals are now failing. Add the San Benito Valley’s summer heat, regularly 15-25°F hotter than Santa Cruz or Monterey, plus the day-to-night temperature swings, and seal failure shows up earlier here than in coastal towns. The wind that funnels through Pacheco Pass works door hardware and drives air infiltration through any gap the creep has opened.
Our Main Hollister Services
Two services generate most of the calls we take from Hollister homeowners: full door installation on openings that have drifted out of square, and window replacement on units whose seals have failed under the valley’s heat cycling.
Door Installation in Hollister
Doors in Hollister fail differently than doors elsewhere. The slab and the jamb may both be fine, but the rough opening has shifted. A pre-hung door installed without correcting that rack will bind within months. We check the opening with a square and a level before quoting, shim and correct the frame at installation, and write the measured survey into the estimate so you can see exactly what we found. For the full scope of what door work in Hollister involves, see Door Installation in Hollister.
Window Replacement in Hollister
Older downtown homes often need full sash and frame replacement, while 1990s and 2000s tract homes more often need glass-unit replacement inside otherwise sound vinyl frames. Both jobs run into the same local variable: the opening is rarely square. We measure each opening in four places, not two, and the written quote reflects the correction work the opening actually needs. Read the full breakdown at Window Replacement in Hollister.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterWindow Installation in Hollister
Most window installations in Hollister are replacements on homes built in two very different eras, and the approach changes with the house. A 1920s Craftsman near downtown usually has original wood sashes that have drifted out of square over decades of Calaveras Fault creep, while a 2003 tract house on the east side more often needs the insulated glass unit swapped because valley heat cycling has broken the seal. Our Window Installation work always starts with a measured survey of each opening, and that survey becomes the written quote you keep.
Single & Double Hung Windows
Signs you need it
The sash no longer stays open, or the window won’t latch because the frame has drifted out of square.
What it costs in Hollister
Replacement single and double hung windows in Hollister typically run $450-$1,200 per window installed.
How we do it
We remove the old sash and frame, correct the rough opening with shims until it reads square, install the new unit, insulate the perimeter, and trim out the exterior.
Horizontal Roller Windows
Signs you need it
The roller track binds partway across the opening, or the window takes real force to close against one jamb.
What it costs in Hollister
Horizontal roller window installation in Hollister typically runs $450-$1,800 per unit depending on frame material and opening correction.
How we do it
We pull the old sash, check the sill and jambs for fault racking, reset the track on a corrected opening, and install the new roller unit level and square.
Casement Windows
Signs you need it
The crank gear is worn but the real problem in Hollister is often the frame, not the hardware, when the sash no longer seats against the weatherstripping.
What it costs in Hollister
Casement window replacement in Hollister typically runs $550-$1,500 per window installed.
How we do it
We remove the complete old unit, true the opening, set the new casement in place, seal it against air infiltration, and verify the sash seats evenly on all four sides.
What Window Installation Costs in Hollister
| Item | Typical range in Hollister |
|---|---|
| Single or double hung window, standard size | $450-$1,200 installed |
| Horizontal roller window | $450-$1,800 installed |
| Casement window | $550-$1,500 installed |
Does fault creep affect the window price in Hollister?
Yes. Openings that have drifted out of square require shimming and correction work before a new unit goes in, which adds labor. The written survey shows the correction line item before you approve anything.
How long does window installation take in Hollister?
Most standard single-home replacements take one to three days depending on the number of openings and how much correction each one needs. Call (509) 265-6387 for a written estimate.
Impact Windows & Doors in Hollister
Impact windows and doors in Hollister are less about hurricanes and more about the Calaveras Fault. The same ratings that resist windborne debris also create a much stiffer frame and laminated glass assembly that tolerates the constant, low-level racking of fault creep far better than standard units. Our Impact Windows & Doors work pairs the right impact-rated product with an opening that gets corrected and shimmed before the unit is set, so the stress goes into the approved assembly, not the frame.
Impact-Resistant Windows
Signs you need it
You want a window that won’t shatter into large shards, or your home’s openings are already shifting and standard units keep failing at the seals and latches.
What it costs in Hollister
Impact-resistant window installation in Hollister typically runs $800-$2,500 per window depending on size and frame material.
How we do it
We specify a PG or CGI impact unit matched to the opening’s deflection data, correct the rough opening, install the heavier frame with proper anchoring, and document the entire assembly photographically.
Double Hung Impact Windows
Signs you need it
You need an impact-rated unit in a traditional double-hung style, often for a Craftsman home near downtown where appearance matters as much as the glass rating.
What it costs in Hollister
Double hung impact windows in Hollister typically run $900-$2,500 per window installed.
How we do it
We order the double hung with laminated impact glass and a frame stiff enough for the opening, correct any fault racking in the jamb, and install with full perimeter anchoring.
What Impact Windows & Doors Costs in Hollister
| Item | Typical range in Hollister |
|---|---|
| Impact-resistant window, standard size | $800-$2,500 installed |
| Double hung impact window | $900-$2,500 installed |
| Impact-rated door assembly | $1,800-$3,900 installed |
Do impact windows make sense in Hollister if there are no hurricanes?
They do for many homes because the laminated glass and stiffer frames handle the fault-creep racking better than standard units. Ask us for the deflection specs on a specific opening. Call (509) 265-6387 for a written quote.
Will impact windows stop every break-in in Hollister?
No product stops every attempt, but impact-rated laminated glass holds together under blows that would shatter standard glass, which buys time. We explain the specific rating before you buy.
Energy-Efficient Windows in Hollister
Hollister’s summer temperatures regularly run 15-25°F above the coast, and windows here go through steep day-to-night thermal cycling that breaks down insulating glass seals faster than in Santa Cruz or Monterey. An energy-efficient window with the right U-factor and solar heat gain coefficient does two jobs: it cuts the cooling load during 100°F afternoons and it lasts longer under that repeated expansion and contraction. Our Energy-Efficient Windows work specifies glass by the opening’s orientation, not by what’s in stock.
Low-E & Argon Gas Glass
Signs you need it
Your cooling bills spike in summer, or you can feel heat radiating through the glass from inside the house on a hot afternoon.
What it costs in Hollister
Low-E and argon-filled insulated glass in Hollister typically runs $500-$1,400 per window installed.
How we do it
We measure the opening, specify the correct Low-E coating for the window’s sun exposure, order the glass with argon fill, and install it in a frame that’s been corrected for any fault racking.
UV-Blocking & Fade Protection
Signs you need it
Furniture, flooring, or woodwork near windows is fading unevenly, with the damage concentrated on the sun-facing side of the house.
What it costs in Hollister
UV-blocking glass packages in Hollister typically add $150-$400 per window over the base insulated glass unit.
How we do it
We select the glass coating that blocks the most UV without darkening the room, then install it in the existing or replacement sash with a written spec sheet for the glazing.
What Energy-Efficient Windows Costs in Hollister
| Item | Typical range in Hollister |
|---|---|
| Low-E argon insulated glass window | $500-$1,400 installed |
| UV-blocking glass upgrade | $150-$400 per window added |
| Full energy retrofit, per opening | $600-$1,600 installed |
Which glass rating matters most in Hollister’s heat?
Solar heat gain coefficient usually matters as much as U-factor here, because the valley sun drives cooling costs. We’ll show you both numbers for every glass option. Call (509) 265-6387 for a written estimate.
Will efficient windows pay for themselves in Hollister?
The payback depends on the window’s orientation, the condition of the old units, and your cooling usage. The written quote includes the glass specs so you can run the numbers yourself.
Sliding & Patio Doors in Hollister
A sliding patio door in Hollister rides on a track that may no longer be straight, because the floor framing under it has moved with the Calaveras Fault. The first thing we check is whether the track reads level and the jambs read plumb, because installing a good door into a racked opening just moves the binding problem from the old unit to the new one. Our Sliding & Patio Doors work corrects the opening before the new door ever goes in.
Patio Doors
Signs you need it
The door was fine for years but now drags at one point in the track, or the latch no longer lines up with the strike plate.
What it costs in Hollister
Patio door replacement in Hollister typically runs $1,500-$3,500 depending on size, glass, and how much the opening needs correction.
How we do it
We pull the old panel, check the subfloor and jambs for fault movement, level and shim the opening, install the new door, and adjust the rollers until the panel moves with one hand.
Sliding Glass Door Replacement
Signs you need it
The glass seal has failed and the panel is fogged, or the frame is so worn that new rollers won’t fix the drag.
What it costs in Hollister
Sliding glass door replacement in Hollister typically runs $1,500-$3,200 per door installed.
How we do it
We measure the rough opening in three places, order a door built for those dimensions, remove the old frame completely, correct the opening, and set the new unit with new weatherstripping and hardware.
What Sliding & Patio Doors Costs in Hollister
| Item | Typical range in Hollister |
|---|---|
| Patio door replacement | $1,500-$3,500 installed |
| Sliding glass door replacement | $1,500-$3,200 installed |
| Screen door installation | $150-$450 installed |
Why do sliding doors bind in Hollister specifically?
The Calaveras Fault’s continuous creep shifts the floor and wall framing under the door, so the track is no longer straight. We correct the opening at installation, but the ground keeps moving afterward. Call (509) 265-6387 for a written quote.
Can you fix the track without replacing the whole door in Hollister?
Sometimes, if the track is the only failed part and the panel seals are still sound. We’ll tell you what the survey shows and quote only the work the opening actually needs.
Impact Garage Doors in Hollister
An impact garage door in Hollister is a wind-load rating question more than a hurricane question, and the answer depends on the door’s size, the house’s exposure, and the fault-drift correction the opening needs. The wide door opening catches the wind that funnels through Pacheco Pass, and a door that isn’t rated for that load flexes and wears its hardware faster. Our Impact Garage Doors work starts with a measured survey of the opening and a written load calculation before any product is specified.
Garage Door Replacement
Signs you need it
The door binds partway up the track, the panels show cracks at the joints, or the frame has moved enough that the door no longer seats evenly against the weatherstrip.
What it costs in Hollister
Garage door replacement in Hollister typically runs $2,500-$4,500 depending on door width, material, and the correction the opening needs.
How we do it
We remove the old door and track, square the opening with shims, install a wind-rated door matched to the opening’s measurements, and set the track so the door runs true.
Wind-Load Code Compliance
Signs you need it
Your home inspector flagged the garage door for wind-load compliance, or the door visibly flexes when the Pacheco Pass wind hits it squarely.
What it costs in Hollister
Bringing an existing garage door into wind-load compliance in Hollister typically runs $800-$2,000 in reinforcement and hardware work.
How we do it
We assess the door’s current bracing, add or replace struts and hardware to meet the required load rating, and document the finished assembly photographically.
What Impact Garage Doors Costs in Hollister
| Item | Typical range in Hollister |
|---|---|
| Garage door replacement | $2,500-$4,500 installed |
| Wind-load compliance retrofit | $800-$2,000 per door |
| New impact-rated garage door, wide opening | $2,800-$4,800 installed |
Is an impact garage door worth it in Hollister when there are no hurricanes?
For many homes it’s less about storm risk than about the wind loads off Pacheco Pass and the stiffness an impact-rated door adds. We’ll show you the load calculation before you decide. Call (509) 265-6387 for a written estimate.
Does fault creep affect the garage door track in Hollister?
It can. As the floor and header drift, the track bows and the door rubs. We square the opening and re-set the track when replacing the door, then document the correction in writing.
Custom & Geometric Windows in Hollister
The downtown Craftsman homes in Hollister often have window shapes you don’t order from a catalog: half-rounds, eyebrow arches, triangle transoms, and other geometric openings built into the original architecture. Replacing those in a house that’s been moving on the Calaveras Fault for 80 or 100 years means the new unit has to be fabricated to the opening’s actual measurements, not the original blueprints. Our Custom & Geometric Windows work runs every opening through a template before any glass is cut.
Geometric & Shaped Windows
Signs you need it
The original shaped window is a single-pane wood sash that’s leaking air, or the glass is cracked because the surrounding frame has shifted and pinched it.
What it costs in Hollister
Shaped and geometric window fabrication and installation in Hollister typically runs $700-$2,500 per window depending on shape complexity and frame material.
How we do it
We template the actual opening, send the exact shape to the fabricator, build the new unit to match the drift, not the blueprint, and install it with a corrected frame.
Oversized Openings
Signs you need it
The opening is too large or too irregular for a standard window, often a picture window with a transom above or a broad opening across a living room wall.
What it costs in Hollister
Oversized custom window installation in Hollister typically runs $1,800-$3,800 per opening depending on glass area and structural reinforcement.
How we do it
We measure the opening at multiple points, calculate the deflection limits on the header and jambs, order the unit to those numbers, and set it with the correction work written into the quote.
What Custom & Geometric Windows Costs in Hollister
| Item | Typical range in Hollister |
|---|---|
| Shaped or geometric window | $700-$2,500 installed |
| Arched or curved window | $850-$2,800 installed |
| Oversized custom opening | $1,800-$3,800 installed |
Can you match a historic Craftsman window shape in Hollister?
Yes. We template the actual opening, including any drift, and order the new unit to those dimensions so it fits the house as it stands now. Call (509) 265-6387 for a written quote.
Will a custom window take longer to get in Hollister?
Custom fabrication adds lead time, typically a few weeks depending on the shape and manufacturer. The written estimate includes the fabrication schedule before you commit.
Brands We Service in Hollister
We install and service windows and doors from CGI, CWS, ES Windows, and ECO Window Systems in Hollister, along with the rest of our manufacturers. Parts availability for standard units is local, with custom fabrications ordered to your opening’s actual dimensions. See our brands for the full line card.
Pricing for Windows & Doors in Hollister, CA
| Service | Typical range in Hollister |
|---|---|
| Single or double hung window | $450-$1,200 installed |
| Casement window | $550-$1,500 installed |
| Horizontal roller window | $450-$1,800 installed |
| Impact-resistant window | $800-$2,500 installed |
| Low-E argon insulated glass window | $500-$1,400 installed |
| Sliding glass door replacement | $1,500-$3,200 installed |
| Garage door replacement | $2,500-$4,500 installed |
| Custom or geometric window | $700-$2,500 installed |
Prices in Hollister push toward the top of these ranges when an opening has drifted significantly out of square from Calaveras Fault creep and needs real correction work, and when the home is older and the surrounding frame requires repair before a new unit can be set. Every quote is a written price before any work starts, built from a measured survey you keep.
Neighborhoods We Serve in Hollister
We work across Hollister, from the historic Craftsman streets near downtown to the tract subdivisions on the east and north sides. Each area has its own housing era and its own fault-drift profile, and we quote based on what your specific opening actually measures.
- Downtown and historic districts
- Eastside tract subdivisions
- North Hollister developments
- Rural residential parcels on the valley floor
- Westside and San Benito River area homes
Response times across Hollister run a little longer for rural parcels on the valley edges than for in-town neighborhoods, and we’ll confirm the scheduling window when we book your measured survey.
Service Area - Cities Near Hollister
From our San Francisco Bay Area office, we serve Hollister and the surrounding communities. That includes Gilroy, CA, Salinas, CA, Watsonville, CA, and Morgan Hill, CA. The fault-creep conditions vary by community, and we adjust the opening correction work accordingly.
Serving Hollister, CA - Our Local Coverage Area
We’re based in the Hollister area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Windows & Doors in Hollister
Most direct window replacements in Hollister don’t require a permit, but openings that are being enlarged or structurally altered usually do. We confirm the permit requirement for your specific job in writing before any work is scheduled.
Most single-home window replacements finish in one to three days. Correction work on fault-drifted openings and any repairs to surrounding framing add time, and the written estimate includes the schedule.
We serve the full city of Hollister plus nearby communities including Gilroy, Salinas, Watsonville, and Morgan Hill. Schedule a measured survey and we’ll confirm availability for your address. Call (509) 265-6387 for a written estimate.
What happens when you call
- 1A real person answersNo phone trees - talk to a local windows & doors pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Hollister Customers Say
"Front door install went smoothly. Written warranty, clear price, no pressure to upgrade anything."
- Nils H."Patio door had dropped and would not lock. They adjusted it rather than selling me a new one, and charged accordingly."
- Simone T."The survey measurements and the quote were the same piece of paper. Nothing changed on install day, which is not what happened with the two other companies we had out."
- Annette R.